Foil Spinners and Heat Shrinkers

swivelWheels-img
 
$2,895.00
$2,300.00


Spinning head mounted on pneumatic column. Push button to apply foil.
Movie of unit.

  • For aluminum, tin, and polylaminate foils. Works with foils from all manufacturers.
  • This system provides the most consistent application of capsules.
  • 800 per hour
  • To operate: Place capsule on bottle and bottle on platorm. Push button (lower right in photo). Bottle is automatically raised, foil applied, bottle lowered.
  • The height of the roller unit is easily adjusted on the stand to accomodate bottles from 7" to 15".
  • 110V, 0.3HP, 3.6A
  • maximum capsule length 60 mm
  • For bottle neck diameters 25 to 33 mm.
  • 1400 RPM
  • bronze rolling spindle
  • adjustable rolling pressure
  • You need a small air compressor. 2 scfm is sufficient.
  • Adjustment on stand is self-evident. Top of bottle should be ~1" below spinner head. Set regulator on unit (on back, not visible in photo) to 5-6 bar (75-90 psi). Set your compressor regulator to >90 psi.

swivelWheels-img
 
$1,995.00
$1,500.00

  • For aluminum, tin, and polylaminate foils. Works with foils from all manufacturers.
  • Same roller unit as the Table Top model but mounted on stand. Lever lowers roller onto bottle and then springs back when released. Easier and faster than Table Top alone.
  • The height of the roller unit is easily adjusted on the stand to accomodate bottles from 7" to 14".
  • 110V, 0.3HP, 3.6A
  • maximum capsule length 60 mm
  • For bottle neck diameters 25 to 33 mm.
  • 1400 RPM
  • bronze rolling spindle
  • adjustable rolling pressure

swivelWheels-img
 
$1,395.00
$1,200.00


Place the spinner on table top. Push baseplate up against edge of the table as in photo above.

  • For aluminum, tin, and polylaminate foils. Works with foils from all manufacturers.
  • 110V, 0.3HP, 3.6A
  • maximum capsule length 60 mm
  • For bottle neck diameters 25 to 33 mm.
  • 1400 RPM
  • bronze rolling spindle
  • adjustable rolling pressure

  $250.00

 

Improved model with fan assisted heating

  • Fan blows heat for more uniform and professional application.
  • 110 V. 1000 Watts (compared to 700 watts on similar units)
  • Takes ~1 second to shrink PVC capsule.
  • Simply lower unit until Stop touches bottle, then remove. Fast, consistent and easy.
  • 3-position switch. Off, Fan only, Fan and Heat.
  • maximum capsule diameter 40 mm
  • max capsule length 70 mm
  • 304 Stainless Steel
  • Please note this unit gets hot. Leave the fan on (Position I on the switch) for several minutes after use for faster cooling.
  • Two units are recommended if you wish to operate continuously for more than 2 hours. Alternate between units every hour.
  • New units often give off an acrid odor. We recommend turning on outside the first time.

  $175.00

 

  • 304 Stainless Steel
  • 110 V, 1000 Watts
  • Takes ~1 second to shrink PVC capsule.
  • Quickly slide bottle neck into heating element.
  • Heating element has perforated stainless safety cover
  • maximum capsule diameter 40 mm
  • Two units are recommended if you wish to operate continuously for more than 2 hours. Alternate between units every hour.
  • New units often give off an acrid odor. We recommend turning on outside the first time.